New Diesel Products for your Ride

Ram Eco Diesel Leveling Kit

If you own a 20013-14 Dodge Ram 1500 4×4 and want to level the stance, MaxTrac has a solution.  The new MaxTrac Suspension 4WD leveling kit features a 1-inch coil spacer as well as a 1.5-inch strut spacer. This design offers 2.5 inches of lift overall.

-Advertisement-
-Advertisement-

The design allows correct A-Arm angle and doesn’t over extend the throw of the ball joint, eliminating premature ball joint failure.

Unlike some companies who use a 2.5-inch coil spacer, MaxTrax splits the difference with the coil spacer and strut spacer to keep the strut from topping out. Spacers are finished in a signature gray, high-quality powder coat for durability and rust prevention.

MaxTrac Suspension LLC
877.929.3015
MaxTracSuspension.com

LED Brake Light Receiver Hitch Cover

Covering your receiver hitch opening keeps dirt out of your hitch box. Now you can add a third brake light at eye level for those little cars on the road.

This light 2-inch receiver features a plug-in brake light that features 12 LEDs for improved visibility and uses a 4-pin slip fit plug that taps into the brake light circuit in your 4-pin trailer plug. A ½-inch-thick foam gasket keeps the housing snug in the receiver.

Harbor Freight
800.423.2567
HarborFreight.com

Cummins Swap Intercooler Kits

When you’ve got your new diesel swap engine in place, wired and nearly ready to go, it’s time to consider the intake plumbing. The last details include having tubes bent for the intercooler. Save the money on custom tube bending and order a pre-made set from Diesel Conversion Specialist. Intercooler tubing kits are complete with tubing, silicone boots and clamps, and are available for Cummins conversions in Ford trucks from the early ‘90s through 2008. The ’08 to current kits are under construction.

Diesel Conversion Specialists
406.755.8878
DieselConversion.com

Kelly Edge A/S Tire

Among the features of the new Kelly Edge A/S are biting tread block edges for all-season traction in wet, dry and snowy conditions; broad tread grooves that help evacuate water and slush from the tread for enhanced grip; sturdy tread blocks to help stabilize the tread footprint to promote long treadwear and a proven tread pattern that enhances handling. The tires carry a 55,000- mile/85,000-kilometer tread life limited warranty.

A broad lineup of 51 sizes will be offered, covering T, H and V speed ratings, and 14- to 18-inch rim diameters within the performance and commuter touring product areas.

Kelly Tires
KellyTires.com

MaxPro Reverse Brake Bleeder

Phoenix Systems offers the heavy duty MAXPRO – a reverse brake bleeding system that allows automotive service professionals and D.I.Y’ers to efficiently perform one-person brake bleeding service, even on ABS systems. The MAXPRO is constructed from durable die-cast steel and aluminum, and the brake bleeder is designed to withstand the rigors of professional use.

Rather than pushing air and fluid down through the system, as in the standard convention, the MAXPRO reverses this process. The trapped air in a brake system, which naturally wants to rise, is pushed up to the master cylinder with a MAXPRO. Properly bleeding your brakes will create a firmer pedal, increased braking power, responsiveness, and reduced vehicle stopping time.

Phoenix Systems
435.673.0777
BrakeBleeder.com

LED Plate Frame

This LED license plate frame features both a brake light and a running light. It houses five red and 11 white LEDs. The white lights illuminate the license plate while the red ones can be wired as an extra brake light and running light.

United Pacific
866.327.5288
Uapac.com

LLY Duramax 3″ High Flow Intake Y-Bridge

Replace your factory restriction intake manifold pieces with a Dirty Hooker Diesel (DHD) LLY High Flow Intake Kit. This kit is a complete one-piece intake manifold upgrade.

The intake is assembled from cast aluminum which allows for a massive increase in intake volume. When compared to the factory intake plumbing, the DHD high flow intake bridge flows an impressive 152% more volume. This intake will not only increase horsepower, torque and airflow throughout the engine, but it will also reduce EGTs and drive pressure. The reduction in EGT and drive pressure will help yield a longer running, healthier engine.

This kit includes the main intake assembly and all necessary hardware for installation. DHD recommends the 700-125 or 700-155 Fuel Block Upgrade kit when installing a DHD, LLY High Flow Intake.

Dirty Hooker Diesel
989.479.0444
DirtyHookerDiesel.com

CP-Carrillo High-Performance Diesel Pistons for Duramax Applications

CP-Carrillo is excited to introduce diesel pistons for Duramax applications.  These pistons include the advanced features and improvements that CP-Carrillo has developed through rigorous testing and R&D.  They are ready for immediate delivery and are for the most popular Duramax applications. Manufactured from 2618 T-61 alloy for structural support and durability, these pistons come completely hard Anodized to withstand turbocharging, supercharging and nitrous.

CP-Carrillo
949.567.9000
CP-Carrillo.com

Cummins Exhaust Manifolds

BD Diesel Performance offers Cummins owners the ultimate in exhaust manifold upgrades. BD’s T4 and T6 exhaust manifolds are perfect for high performance, high RPM 5.9L and 6.7L engines. They offer better cylinder exhaust evacuation that helps to keep EGTs down. T4 and T6 3-piece ‘Ported’ exhaust manifolds feature larger runners that enhance flow through the manifolds with no restriction throughout rpm range. The center face mount can face up or down, at the optimum 20°  (rather than 40°) angle. This helps when mounting S400, S500, or other larger turbochargers.

BD Diesel
800.887.5030
DieselPerformance.com